Midea Dehumidifier Eb Error Code: What It Means and How to Fix It

By Dan Mercer · Published October 5, 2026 · Updated October 6, 2026 · Codes covered: Eb · Sources

Verify in your manual: Midea lists Eb for pump-feature units. Cube manuals also show Eb when the unit is lifted off its bucket. Non-pump models use P2 instead. Check your model's manual.

Eb on a Midea portable dehumidifier means the bucket is removed or not in the right position. Midea lists it for models with a built-in pump. It nearly always shows up right after the bucket was emptied, and most owners clear it in a minute or two by reseating the bucket.

Everything on this page is optional DIY that you do at your own risk. If you're unsure, stop and contact Midea.

This 3-minute fix saved 0 homeowners a technician visit this month.

What the Eb code means

Midea's Error Codes and Protection Code table defines Eb as: "Bucket is removed or not in right position – Replace the bucket in the right position. (only available for the unit with pump feature.)" Midea's US dehumidifier FAQ uses the same wording.

What you'll see: in Midea's pump-model manual, if you pull the bucket out while the unit is on, the compressor and fan turn off, the unit beeps 8 times, and the display shows Eb. If the unit is off when you pull the bucket out, it still beeps 8 times and shows Eb. So a beep-and-Eb as you empty the bucket is expected. It only becomes a problem if Eb stays after the bucket is back in.

Cube models (the unit sits on top of its bucket): Midea's Cube manual says that if you lift the unit off the bucket while it's running, the display shows Eb and the unit stops until you put it back on the bucket or switch to bucketless mode.

Look-alike codes that mean something else:

• P2 – the bucket is full. On non-pump models, P2 also covers a bucket that's out of position, so those units show P2 instead of Eb. See our P2 page.
• AS – humidity sensor error.
• ES – evaporator tube temperature sensor error.
• EC – refrigerant leakage detection. This is not a bucket problem (see Safety notes).

Likely causes (most common first)

1. The bucket isn't all the way in after you emptied it.
2. The bucket got bumped and slid partway out.
3. The pump hose or filter fell off when the bucket came out. It can keep the bucket from seating, and Midea says the pump won't work properly without the filter.
4. Something is blocking the bucket opening, like a towel, the hose, or packing material.
5. A Cube unit isn't sitting square on its bucket, or was meant to run in bucketless mode but that mode isn't on.
6. A fault inside the unit. If Eb stays on with the bucket properly seated, the problem is inside the unit and needs service.

How to fix it, step by step

Unplug the unit before each hands-on step. Check whether Eb clears after each one.

1. Reseat the bucket as described in Try This First. Midea says to push it gently all the way in, and not to touch any parts inside the unit while the bucket is out.
2. Reattach the pump hose or filter if it dropped. Midea's FAQ describes the filter as a long tube with a round filter on the end. Reinstall it, then put the bucket back in.
3. Clear the bucket opening. Take out anything that keeps the bucket from going straight in.
4. On Cube models, reseat the unit on the bucket. Lift with proper technique, line it up, and set it down squarely. Midea says to make sure it's seated properly.
5. On Cube models, turn bucketless mode back on if you use it.
   • Midea says bucketless mode has to be turned on within 3 minutes of plugging the unit in.
   • Connect the continuous drain hose first. It must slope down and never rise above the drain port.
   • Plug in, then hold the UP and FILL LEVEL buttons together for 3 seconds until the bucketless icon appears.
   • Midea's auto-restart after a power cut doesn't bring bucketless mode back. If the power went out, you'll need to turn it on again.
6. Restart and wait a few minutes. Give it the 3-minute compressor delay.
7. Stop here if Eb won't clear with the bucket (or Cube unit) properly seated. Do the checks under Test the part, then contact Midea.

Test the part

You don't need a multimeter for Eb. These checks are visual and safe for owners. Don't open the case.

1. Unplug the dehumidifier.
2. Check the bucket. Make sure it isn't cracked or warped and that nothing is stuck to its back edge. Midea recommends washing it every few weeks with mild detergent and water, not in the dishwasher.
3. Check the float or full-level piece, if your bucket has one. It should move freely and not be stuck with grime. Don't bend or force it.
4. Check the pump filter tube on pump models. Make sure it's attached and clean. Midea says the pump won't work properly without it.
5. Do a test fit. Slide the bucket in gently. It should go all the way in without catching.
6. Stop if everything looks fine. Don't remove panels, test wiring, or touch the refrigeration system. If Eb won't clear after these checks, the bucket sensor or switch inside may need service.

Safety notes

When to call a pro

• Eb won't clear with the bucket or Cube unit properly seated, after Try This First and the steps above.
• The pump light keeps blinking even after you've cleaned the pump filter, checked the hose, and emptied the bucket. Midea says to contact Customer Service if that happens.
• Water leaks from the cabinet, or the display shows EC, AS, or ES.
• The unit is under warranty. Call Midea before attempting any repair.
• There's water damage. Mold or warped flooring needs a remediation or flooring pro.

Midea's US manuals list the Service Center number as 1-866-646-4332. Have your model number ready. It's on the silver nameplate on the back.

FAQ

Related

• Midea Dehumidifier EC Error Code
• Midea Dehumidifier P2 Error Code
• AprilAire Dehumidifier E2 Error Code
• AprilAire Dehumidifier E3 Error Code
• AprilAire Dehumidifier E4 Error Code
• AprilAire Dehumidifier E7 Error Code
• All dehumidifier error codes